Bosch injection pump in exchange

LT part number: 1015544
Original item number: 0460424479
Article specification:
Brand: CNH
Synonyms: 0460424410 0460424414 504246318 504374949 L202-R2076 N504246318 N504374949
Tags: 75C T4020 T4030 Quantum T4030F T4030N T4030V T4.75N T4.75V T4.75F T4.75LP 75N 75V TD4020F TD4030F TD4040F TK4030 TK4030F TK4030V

CHF 2,357.00

CHF 2,357.00

excl. VAT
Not Available

    This combination does not exist.

    Units of Measure: Units
     Add to basket

    Warranty conditions
    12 months manufacturer's warranty from date of delivery.
    The warranty expires if,
    - The installation is not carried out by a qualified professional.
    - The pump is opened or otherwise tampered with.
    - If the wrong or contaminated operating materials are used.
    The LT-Shop does not assume any assembly and disassembly costs.

    Product information:

    The following faults may occur at ambient temperatures of -15°C or when the engine block has cooled down
    1. the injection pump is leaking in the area of the SV piston covers or KSB.
    The leakage stops when the engine reaches normal operating temperature.
    2. engine does not start or stalls after starting.

    Troubleshooting
    If one or both faults occur, replace the standard seals with the following new seals.
    Drive shaft seal 20x31x7.3 9968111
    O-rings 9968113 +9971754 (SV piston cover) (KBS cover) (KBS shaft)
    Pumps that have been converted accordingly are marked with a letter on the pump flange!
    Correct the injection setting in the workshop manual for series F5C/F5A engines.

    Specifications for injection setting of the fuel injection pump.

    The injection pump injection adjustment procedure for Series F5A and F5C IVECO engines differs from the static injection pump injection adjustment procedure described on page 22 of the Case engine repair manual 87693888 and the New Holland engine repair manual 87693890 for F5A and F5CE engines.

    The engine workshop manuals show the incorrect advance mechanism on page 22, section 3. The manuals illustrate the hydraulic early adjustment mechanism (KKSB). The F5A and F5C engines with Bosch VE injection pump currently set the wax engine cold start advance mechanism (KSB) and provide six degrees of advance for cold starts.
    Setting the injection pump timing:
    Turn the engine clockwise as viewed from the front of the engine. Turn the engine flywheel to TDC of cylinder number 1 using the engine turning tool (part number 380000732) with adapter plate (part number 380000988) and the following conditions are met.

    The timing adjustment notch is visible from the inspection window.
    On F5A engines, the tool (part number 380000150) is inserted through the guard plate into the hole on the flywheel housing (exhaust manifold side).
    On F5C engines, the tool (part number 380000150) is inserted through the guard plate into the hole in the flywheel.
    To measure the stroke of the injection pump plunger in relation to the TDC of the engine:
    Use a dial gauge (tool part number 380000228) together with the adapter (tool part number 380001601).
    NOTE: It is extremely important that you energise the KSB (wax motor) with a 12-volt supply at least five minutes before checking the injection pump injection setting. This will remove the six-degree cold start advance on the pump.

    1. remove the piston access plug in the centre from the rear cap of the injection pump.
    2. install the injection pump timing adjustment adapter tool (part number 380001601) and the pin in the hole. Tighten the adapter.
    3. ensure that the KSB early adjustment is retarded with the arm pushed forwards (towards the front of the pump) almost against the stop.
    4. insert the dial gauge (special tool part number 380000228) into the guide tube and pretension the dial gauge needle by 2.5 mm. Pull the end of the shaft outwards and release it to ensure that the dial gauge needle moves freely and does not jam. The dial gauge needle must move freely immediately. If it does not, reposition the dial indicator until the needle moves freely in the shaft. 5.
    5. turn the motor anti-clockwise (as seen from the front of the motor), observe the dial gauge needle drop to the minimum reading and the end of the movement. It is now in the valley between two cams.
    6. set the dial of the dial gauge with the indicator needle to zero.
    7. turn the engine clockwise (as seen from the front of the engine) until the locking pin falls into the hole in the flywheel and locks the engine at TDC. Ensure that the reading on the dial gauge matches the technical data below. Dial gauge readings correspond to engine power in kW as listed below.
    This measurement is the stroke that the injection pump plunger moves when the flywheel is turned to TDC (Top Dead Centre).


    Engine power Injection setting at TDC New Holland models Case/CaseIH
    44 kW 0.80 mm at TDC +/-0.05 mm TD5010, Farmall 60
    48 kW 0.76 mm at TDC +/-0.05 mm T4020 and T4020 Deluxe Farmall 65, 65C,65U
    53 kW 0.80 mm at TDC +/-0.05 mm TD5020, Farmall 70
    55 kW 0.75 mm at TDC +/-0.05 mm L180,420,420CT Series 3
    55 kW 0.88 mm at TDC +/-0.05 mm L223, C227 SR200, TR270
    57 kW 0.76 mm at TDC +/-0.05 mm T4030 and T4030 Deluxe Farmall 75, 75C and 75U
    60 kW 0.80 mm at TDC +/-0.05 mm TD5030, Farmall 80
    61 kW 0.88 mm at TDC +/-0.05 mm L225, C232 SR220, SV250
    61 kW 0.88 mm at TDC +/-0.05 mm L185, C185 430, 435, 445 and 445CT Series 3
    65 kW 0.76 mm at TDC +/-0.05 mm T4040, T4040V, T4040F Farmall 85N
    67 kW 1.00 mm at TDC +/-0.05 mm L230, C238 SR250, SV300, TR320, TV380
    8. if necessary, loosen the fixing screws of the injection pump and turn the injection pump housing until you obtain the correct dial gauge reading.
    9. check the start of injection again. This is necessary because play in the engine control unit can influence the start of injection. When you are sure that you have set the injection start correctly, tighten the fixing screws of the injection pump to 24 Nm. 10.
    10. remove the 12-volt jumper cable from the KSB.
    11 Remove the dial gauge and the adapter.
    12. install the piston access plug and tighten it to a torque of 28 Nm.
    13 Remove the TDC locking pin from the flywheel. 14.
    14. remove the engine turning tool (part number 380000732) and the adapter plate (part number 380000988) from the engine.

     Checkout


    Quality parts
    Original & OEM
    Return right
    10 days
    Next day delivery
    in Switzerland
    Worldwide
    Delivery with UPS

    Share this article

    No Specifications
    Accessories
    This is a preview of the recently viewed products by the user.
    Once the user has seen at least one product this snippet will be visible.
    Recently viewed articles